Specialized Products S P - Concrete Coatings Decorative ...
Concrete Coatings Inc. acrylic overlays pressure at higher air flow is preferred. Stay about 16” above the surface. Ensure all tape lines are covered consistently. floor scraper to remove extreme high spots. DO NOT push down on the ... Get Content Here
Mechanical Concrete Preparation - Profiling With A Grinder ...
Grinding the surface with a floor grinder, scarifier, or shot blaster is the preferred method for profiling your floor. You then have to allow it to dry before applying any coatings. Most contractors use a Floor Grinder with diamond plates to roughen 2:43 Concrete Floor Grinder by ... View Video
SONOSHIELD TUF-TRAC AND TUF-TRAC ACCESSORIES - Cadeco
Concrete Tennis courts Playgrounds Arenas Walkways Balconies Steps Bike paths TRAFFIC COATINGS 97577 250 Tuf Trac and Acces 9/21/01 4:15 PM Page 1. profiling is the preferred floor preparation method. Mechani-cally profile the floor to a ... Get Content Here
Design Of Slabs That Receive - ACI - American Concrete Institute
Section 09963 Elastomeric Coatings. When preparing specifications for different flooring team might have preferred. The design team should not leave the testing to the floor for Determining Relative Humidity in Concrete Floor ... Get Content Here
About Experts Sitemap - Group 164 - Page 6 2012-07-20
Thank you for your question Bill, With some contractors there will always be a preferred method for those who are too lazy or not wanting to potentially lose an install due Flooring and Carpeting: concrete floor coatings: ... Read Article
Preferredservicellc
Satin Floor Coatings; and the EnviroStar Green Hard Floor System. In addition, EnviroStar Green Mild Acid for concrete, stone and Similar marble and quarry tile hard floor surfaces. Non-volatile solids 20% Non-volatile solids 22% 1 .06 us gal. ... Doc Viewer
UNIVERSAL FLOOR PREPARATION GUIDELINES
UNIVERSAL FLOOR PREPARATION GUIDELINES - First prep concrete by preferred method, alkyd, or latex coatings. Light gray color permits good coverage with first finish coat * Used over concrete or masonry (glazed brick, vinyl tile, ... Read Here
Passive Fire Protection - Wikipedia, The Free Encyclopedia
During fire testing of concrete floor slabs, water can be seen to boil out of a slab. intumescent coatings are preferred aesthetically and performance-wise. It should be noted that in the eventuality of a fire, ... Read Article
KEMIKO STONE TONE SEALER II & Industrial Coatings
KEMIKO® STONE TONE SEALER IIis applied to properly prepared concrete, schools, shopping malls, and many other interior floor surfaces requiring additional protection. Excellent replacement product for high VOC lacquers, acrylics Blas-Trac is preferred for long term adhesion and non-slip ... View Document
CONCRETE SEALER, DENSIFIER, AND CHEMICAL HARDENER
FLOOR SHIELD CONCRETE SEALER, DENSIFIER, AND CHEMICAL HARDENER Wet curing is the preferred recommendation on new concrete, however, if a chemical curing compound is to be used, sealing agents unless these coatings have been removed by chemical or mechanical abrasion. ... Retrieve Doc
About Experts Sitemap - Group 207 - Page 10 2012-07-20
Concrete floor coatings, tony dear, dear tony: seal coating: Hi Joe and thanks for your questions! Our preferred method for sealcoating driveways is the squeegee (brushed on) method. For one simple reason: It puts on a better, even coat. ... Read Article
Penetrating Sealers: A Comparison Of Epoxy, Moisture-Cured ...
Tems. Traditionally, the preferred surface preparation method is abrasive blasting of penetrating sealers are often used for floor-ing systems. Coatings on green concrete and paste; aggregate is fractured from blasting Fig 4 ... Retrieve Here
SUMMARY - Floorcare USA - High Performance Concrete Coatings
Installed is preferred to achieve best results) a. Overall FF50 or higher b. coatings and finishes. www.nfsi.org. 1.03 SUBMITTALS A. Finish concrete floor surfaces in accordance with ACI 302.1R. ... Document Retrieval
HIGH-BUILD PRIMER - Kong-Crete Finishes - Decorative Epoxy ...
• Concrete How to Apply Surface Preparation 1. Mechanical surface profiling is the preferred floor preparation method for both new and existing floors. and floor coatings in accordance with the manufacturer’s instructions. PRODUCT DATA ... Retrieve Content
Scotchkote Urethane Floor Coating FB 857
With a degree of flexibility for application to concrete and asphalt floor surfaces. Existing Coatings: should first be checked for adhesion to the with medium pile being preferred on uneven surfaces. ... Content Retrieval
046 - Guard Heavy Duty Epoxy Floor Screed
PROTECTIVE COATINGS TECHNICAL DATA SHEET NATIONAL GUARD HEAVY DUTY EPOXY FLOOR concrete or stone surfaces. Can be over coated with National Guard Epoxy Flooring Topcoat S.F. when a high degree of cleanliness preparation are preferred followed by the removal of dust ... Retrieve Doc
EC-100 Spec Sheet - Sticky Feet Manufacturer's Page - Westcoat
Epoxy floor coatings. EC-100 is also used as a sealer Over concrete, shotblasting is the preferred method for preparing concrete when applying epoxy and urethane coatings. When using other methods, prepare the surface ... Document Retrieval
GARAGE FLOOR COATINGS: IDENTIFYING WATERBORNE EPOXIES WITH ...
Our objective was to identify the most effective polymers for garage and concrete floor coatings and to identify any polymers with serious flaws or performance weaknesses. part systems are preferred, two part reactive systems can be used if they require only moderate mixing. ... Doc Viewer
Product Information BD CLASSIC 3300 Epoxy Floor Coating
Coatings such decorative concrete or over acid stained As a Primer: the preferred method for preparing the concrete. Proper 250-300 ft²/gal. concrete floor slab should be below 80% (per ASTM F-2170). ... Fetch Full Source
64011 SK Lock-Down DATA Sheet - Seal-Krete The Professional's ...
SealTM, Concrete Colors and Floor-Tex®, and improves the adhesion of water-based floor paints, stains and textured coatings. Important: Read directions on can thoroughly. PREFERRED PRIMER FOR SEAL-KRETE EPOXY-SEALTM, ... Retrieve Document
ART PREFERRED VENDORS CUSTOMIZED APPAREL GOLF CARTS ...
PREFERRED VENDORS January, 2009 All area codes are “330” unless noted. ASPHALT, BRICK & CONCRETE Danjen Striping – 216-272-8135 ASSISTED LIVING FLOOR COATINGS Terra Coat – 216-254-8157 FLORIST - RETAIL ... Document Viewer
GUIDELINE INSTRUCTIONS FOR CONCRETE SURFACE PREPARATION
Guide Specification for “Cast in Place Concrete for Floor Slabs on Ground That Will Receive Semi-Permeable or The preferred methods for creation of a surface profile, SSPC The Society for Protective Coatings, 40 24th Street, 6th Floor, Pittsburgh, Pa. 15222-4643, (412) 281- ...Mechanical Concrete Preparation - Profiling With a Grinder
MECHANICAL CONCRETE PREPARATION
Profiling With a Grinder
What You Need:
•Floor Grinder
•Broom or Shop-Vac
•Hand Grinder
•Eye Protection
•Disposable Respirator
No matter how new or clean the concrete is; it will need a rough textured surface, similar to 100 grit sandpaper, in order to achieve maximum epoxy adhesion. A good rule of thumb is; the rougher the concrete, the better adhesion. Grinding the surface with a floor grinder, scarifier, or shot blaster is the preferred method for profiling your floor.
Though acid etching is the easiest, it can sometimes take multiple applications to sufficiently etch the concrete. You then have to allow it to dry before applying any coatings. Most contractors use a Floor Grinder with diamond plates to roughen up the concrete because it doesn't take as long as the acid preparation. You can rent a grinder from a local Big Box store.
This also roughens the concrete much more effectively. Using the grinder will open up the pores of the concrete to allow the epoxy to sink in, therefore achieving maximum adhesion. Grinding also removes oils, grease and other contaminants which prevent the coating from adhering.
To profile the areas the floor grinder cant reach, such as around the baseboards or edges of your concrete, we suggest using a hand grinder. Please make sure you use eye protection during this process.
After grinding your floor, sweep or vacuum the dust and loose debris away. This will ensure that your coating will have a nice and clean surface to adhere to.
After you have finished, you are now ready to apply your first coat of epoxy.
Important Facts:
Also, if youre coating concrete that has been sealed with a sealer, it is necessary to use a floor grinder to prepare the concrete. You cant use a chemical profiler to remove a sealer. Please watch our sealer test video to check if your concrete has been sealed.
View Document
